The Foundation of Plumbing Knowledge When Installing a Bathtub
The Foundation of Plumbing Knowledge When Installing a Bathtub
Blog Article
We've stumbled upon the article relating to Tools You Need to Install a New Bathtub down the page on the net and thought it made good sense to share it with you in this article.
Mounting a bath tub isn't specifically brain surgery, however it does need solid plumbing, woodworking, as well as occasionally, tiling abilities. Changing an old tub with a new one is likewise a moderately difficult task. If the old bathtub is easily available, the project can move quickly; if you need to open a wall to get rid of the old bathtub as well as position the brand-new bathtub, the task is a lot harder. In either situation, the project is within a house handyman's abilities, although you will need an assistant to move out the old bathtub and set in the brand-new one. See to it you have qualified on your own for the job as well as are comfortable attempting it. As opposed to employing a professional to take over a halfway-completed project, it is better to think about using one before you begin. Opportunities are you might require a professional plumber to make tube connections.
This write-up will certainly aid you install a new bathtub in your restroom if you have already purchased a brand-new bathtub as well as do not need to change the arrangement of your previous water pipelines.
Your tools as well as product list need to consist of the following:
Removing Old Touches
If you need to change old taps with new ones as a part of your installment, then the first thing you should do is detach the water supply. After doing so, activate the taps to drain any kind of water staying in the system. The process of eliminating the existing faucets can be quite troublesome due to the restricted gain access to that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a cloth prepared for the staying water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming during this procedure. Once the faucets have been removed, the holes in the bath/basin will need to be cleaned up of any kind of old securing substance.
Before proceeding to fit the brand-new taps, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end offers a connection to the current supply pipes.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the mounting hole in the bath/basin guaranteeing that the washing machines remain in location in between the faucet and also the sink. Safeguard the faucet in position with the maker supplied backnut. As soon as the faucet is securely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular faucet ports. The previous kind must be linked to the tap ends initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Mounting the Tub
Using both wooden boards under its feet, position the tub in the called for setting. The wooden boards are useful in equally spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto four little factors.
The next objective is to ensure that the tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bath tub up until the level reviews degree.
To mount taps, fit the bottom of the furthest flexible faucet connector to the suitable supply pipe by making a compression join; then do the same for the other tap.
Switch on the supply of water and also examine all joints and also brand-new pipework for leakages as well as tighten them if required. Fill the bath tub as well as additionally inspect the overflow outlet and also the normal electrical outlet for leaks.
Finally, take care of the bathroom paneling as explained in the supplier's instruction manual. Tiling and sealing around the bath tub must wait until the bathtub has actually been made use of a minimum of once as this will certainly resolve it right into its final placement.
Preparing for the Installation
First of all, the sustaining frame provided with the bath must be fitted (if called for) according to the supplier's directions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to see to it that if the faucet includes a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to prevent strain on the bathtub.
Fit the versatile tap ports to the bottom of both taps using 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize all of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath need to currently be ready to be fitted in its last position.
Tiling Around the Bathtub
In the area where the bath satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to crack a rigid seal, causing the water to permeate the wall surface in between the bathroom and the tiling, causing problems with wetness and feasible leakages to the ceiling below.
You can select from a variety of coloured sealants to assimilate your components as well as fittings. They are marketed in tubes as well as cartridges, and are capable of securing voids up to a size of 3mm (1/8 inch). If you have a bigger space to load, you can load it with twists of drenched paper or soft rope. Bear in mind to always fill up the bathtub with water before securing, to permit the movement experienced when the bathtub is in use. The sealer can fracture fairly early if you do not think about this motion before sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also quickly offered on the marketplace. It is advisable to fit the tiles utilizing waterproof or waterproof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an avid person who reads about How to Install a Bathtub Yourself, I figured sharing that topic was smart. Are you aware of another individual who is curious about How to Install a Bathtub? Why not share it. Thanks a bunch for your time. Don't hesitate to pay a visit to our blog back soon.
Best in town? Dial. Report this page